In order to solve their own building construction site mixing mortar dust phenomenon, Tel 18962026970 please consult affect air quality, pollution of the environment. Comply with state environmental requirements, the company introduced the German technology manufacturing, set storage, transport, stirring as one continuous dry mortar storage tank. The device has a superior performance, reasonable structure, stir quickly and evenly, low energy consumption, simple operation, easy maintenance and repairs and so on. Suitable for dry powder particle ≤5mm site mixing mortar material. Can meet in masonry, touch needs ash, ground mortar construction of production. More traditional construction methods, since efficiency is greatly improved. The equipment consists of material storage tanks, mixing four parts of the system, the water supply system. Second, the principle storage tank equipment as a dry mortar carrier stored in the construction site, bulk dry mortar transport by truck to the site mortar, dry mortar through the air force delivered to the storage tank, and the use of articulated through the lower end of Continuous mixer for mixing can be. Dry mortar mortar transported to the site by truck, by the pneumatic conveying system for a vehicle, will be transported to the tank mortar, and then use the tank vent removal equipment (bag or water) to remove dust. The dry mortar tank by gravity and vibration body vibration motor to make it even fall through the tank lower end of the flow control valve link, open during normal use at the maximum position. When the dry mortar into the mixer, in a blender advancing end pre-mixing, then compulsory quantitative output by propeller shaft, when the rear end into the mixing provided by the cross-quantitative water pumps, mixing mortar and who through wet mortar, and through the discharge port whereabouts. Standard consistency water valve for manual control (standard consistency water demand is provided by the manufacturer according to product formulation mortar and allow to fluctuate within a certain range), after pressing the start button, vibration motor, the main drive motors, pumps and solenoid valves all started which intermittent vibration motor relay under the control of the practice, and the rest with the stirring time operation, electrical principles: the principle is shown in Figure 4. Third, the technical parameters of a model of the device, storage tank technical parameters of the project model 20m3 22m3 tank diameter mm 2500 2500 mm 6500 7150 tank height weight kg 2200 2400 foot spacing mm 2500 * 2500 2500 * 2500 pass through the feed opening mm DN250 DN250 2, stirring system technical parameters Item Model D100 D150 Dimensions (L * W * H) 2300 * 380 * 350 3000 * 380 * 350 weight kg 150 210 drivers driving voltage power kw 3.0 4.0 v / Hz, 380 / 503 3-phase 380/50 xianggong said the quantity L / min 100 150 Noise db (A) the noise from the device 1m registered as 70db (A) 3, electrical parameters required field power connection: 380V / 50Hz three-phase alternating current, 3 * 160A fuse devices and leakage protection switch, cable 3 * 4mm2 + 1 * 2.5mm2. 4, rotary type level indicator Power: 110V / 220V-50HZ, power 3w, wiring: 1 * 1.5mm maximum signal output: AC: Max 250V, 2A, 500W, DC: maximum 300V, 2A, 600w. Protection class: 1. 5, the water supply system water pump drive power: 0.37kw, diameter: 3/4. Minimum pressure: 3Bar. 6, stir main motor drive power: 3kw power supply: 380V / 50Hz three-phase. 7, vibrator drive power: 0.25kw Voltage: 380V / 50Hz, exciting force: 310kg four, equipment diagram (see drawing) five, requirements and precautions, safety rules 1.1 Special attention must be continuous dry mortar mixer and safety devices on the storage tank, before turning to run every time, health safety devices must be checked. Damage occurs in the safety device type, not allowed to run dry mortar mixer and storage tank, in order to avoid accidents. 1.2 The operator must pass special training, master en-dry mortar mixer and storage tank for use and maintenance of knowledge, but also have the necessary expertise. 1.3 The operator must wear protective equipment (such as: helmets, safety shoes, safety glasses, etc.). 1.4 electrical system is the use of high-current power supply industry operating equipment in operation, there is the danger of power and rotating parts, must ensure safety, prohibit the operator changes the electrical connection on the device. 1.5 when working on the power supply member, a second person must be present in order to open the circuit in an emergency situation, and should never be any part of the object into the body into the machine. 1.6 carry out maintenance work in a continuous dry mortar mixer and the storage tank must be in non-pressure state, according to the provisions of surplus materials as construction waste cleanup. 1.7 Continuous dry mortar mixer and storage tank maintenance must be performed by the manufacturer recognized professionals. 1.8 untrained workers recognized, non-open continuous dry mortar mixer electrical control box. 2, installation and transportation requirements 2.1 Continuous dry mortar mixer and storage tank to be installed at a height position outside the working range of the danger, to minimize moving. To prevent falling objects at the workplace. 2.2 In order to ensure continuous dry mortar mixer and storage tank steady work to ensure the safety and prolong its service life, must be installed on a flat solid concrete floor, concrete grade ≥C25, flatness of not more than 2mm / 2m, thickness not less than 200mm, base area of ??not less than 2500mm * 2500mm. (See diagram of the storage tank and technical parameters) 2.3 material storage tank should be installed to ensure the relative vertical inclination of not greater than 2 °. 2.4 Continuous dry mortar mixer and storage tank using a dedicated back-tanker transportation in the construction site need to move, should consider backing tanker maximum rated load carrying capacity and road transport routes were handling. Tank than expected state of not more than three tons before bad luck. 2.5 Continuous dry mortar mixer and storage tank in the absence of a dedicated back borrowed tanker and transport, can be used trucks and semi-trailers to transport. In lifting hook or wire should be on a dedicated storage tank lug connections. Rigorous climb with ropes holding tank and other parts, not the side, the tank will cause damage and deformation. (Observation tank lifting mark). 3, then electric mixer and storage tank requirements 3.1 Continuous dry mortar mixer and storage tank configured power distribution box, power distribution box by using 3 * 4 + 1 * 2.5mm2 four core cable direct access. 3.2 rigorous two-way power simultaneously access the continuous dry mortar mixer and storage tank of electrical equipment. 4, check the work before the start of the 4.1 Check supply voltage, current is normal. 4.2 Check the water pressure and the water supply is connected properly. 4.3 Check all power cords, plugs, electrical, water supply and safety devices are in good condition. 4.4 verify that all components are installed according to assembly requirements. 4.5 ensure that the housing is well grounded. 5, power supply 5.1 to connect to the water supply pipe systems and continuous stirred tank mixer inlet. 5.2 The trolley into continuous dry mortar mixer mortar exit. 5.3 Open the valve on the storage tank. 5.4 When the demand for water transportation of materials is unknown, the water supply valve fully unscrewed. 5.5 Press the green button to start the machine. 5.6 regulate the water supply valve, know up to standard consistency so far. 6, stop and work interruptions press the red button to stop the machine 6.1. 6.2 downtime and interruption of work more than 30 minutes (the opening hours of practice with the material and ambient temperature) must clean the machine, because the material in the machine will gradually solidified forced to start again will cause the main motor overload. 6.3 In case the machine re-run after a slight change in the consistency of intermittent work, do not immediately change the water setting. Because the variations due to material hardening caused by, in most cases can adjust itself, because only until the hardened material until leaving the continuous mixer. 7, closed down 7.1 operating storage tank butterfly. 7.2 continues to run a continuous mixer until only water from the discharge port so far. 7.3 Press the red button to power off the machine. 7.4 Close the water supply. 7.5 Unplug the power cord plug, cut off the mains. 7.6 according to the procedure to clean the machine. (Note: there is no money to be well grounded, rigorous in the bulk storage tank cylinder were strong electric welding and other operations). Six, electrical schematics (see my factory technical departments drawings). Dry-mixed mortar equipment type (1) raw material pretreatment system equipment are drier and screening machine. Optional vibrating fluid bed dryer, tumble dryer, drying machine, screening machine at home and abroad mainly projection screens, flat screens and other equipment. (2) dosing system can be divided into two batches measurement and continuous measurement mode, the main use of different batches metering metering sensor in the hopper and separate control, continuous measurement of the cumulative weighing the main belt and screw feeder speed Weighing two ways. (3) hybrid system equipment at home and abroad mainly planetary cone mixer, weightlessness mixer, coulter mixer, vertical mixer, pneumatic mixer mixing equipment. (4) packaging system is divided into dry mortar and bulk packaging machines. Packing machine is mainly composed of helical impeller, air blown packaging machine. (5) The dust collection system equipment are cyclones, baghouse dust and other types of equipment. Dry mortar production line equipment selection, equipment selection is the basis for dry mortar production line design critical work. Equipment selection determines many of the key factors supporting the future, investment, production, automation built dry mortar production line and other related devices. Dry mortar production line design selection of equipment into consideration the following factors aspects: product varieties and production, raw materials and additives for silo volume, ingredients, weighing accuracy, mixing processes, packaging production and logistics processes, automation, etc.